Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Fox Chase Homeowners
If you’ve noticed a rusted cap rattling against the flue on a windy night, or a hairline crack spreading across the concrete crown on top of your chimney, you’re looking at the two parts of the system that take the most weather and fail first. In Fox Chase’s freeze-and-thaw winters, water gets into small cracks, freezes overnight, expands, and widens them by spring. A cap that’s lost its screening lets squirrels, birds, and rain straight into the flue. Our technicians have up to 9 years of experience and handle chimney cap & crown work as a routine part of the full chimney service we offer. We can often get to these jobs the same day. Call (844) 526-7704 to book a sweep and inspection.
What Our Chimney Cap & Crown Service Includes
Cap and crown work covers the top of the chimney, which is where most water damage starts. Here’s what each part of the job involves and when it makes sense.
Cap Installation
A chimney cap is the metal or stainless cover that sits over the flue opening and keeps rain, snow, animals, and debris out while letting smoke escape. If your chimney has no cap at all, or only a thin single-flue cover that’s rusted through, a proper installation is the first thing we’d recommend. We fit single-flue and multi-flue caps from brands like Olympia Chimney and Famco, sized to the actual flue rather than a one-size stock piece, and we seal the base so water can’t run down the outside of the flue tile.

Cap Replacement
Caps don’t last forever. Galvanized steel rusts out in a decade or less, and even stainless can pull loose at the mounting legs after years of wind. When a cap is bent, missing screening, or sitting crooked, replacing it is usually less expensive than repairing it. We pull the old cap, check the flue tile and crown underneath for damage the cap may have been hiding, and install a new one with a secure fit and correct clearance.

Crown Repair
The crown is the concrete or mortar cap at the very top of the masonry that sheds water away from the chimney body. When it cracks or separates from the flue, water runs down inside the brick and shows up months later as stains on your ceiling or crumbling mortar. We chip out the failed sections, rebuild the crown with the proper slope, and bond it to the flue so water runs off instead of in. A crown that’s only cracked can sometimes be repaired rather than replaced, which is worth knowing before anyone quotes a full rebuild.

Crown Coating
Crown coating is a flexible, waterproof sealant applied over a crown that’s still structurally sound but showing surface cracks or wear. It’s a good option when the crown is intact but won’t survive many more winters without help. We clean and prep the surface, then apply a coating that moves with the masonry instead of cracking away from it. This is one of those jobs where doing it early saves you from a rebuild later.
Multi-Flue Cap
A multi-flue cap covers two or more flues in a single unit, which is common on older Fox Chase homes with a fireplace plus a furnace flue or a second fireplace. Because there’s more surface area and more weight, the mounting and fit matter more than on a single-flue cap. We measure each flue opening, build the cap to span them correctly, and secure it so it stays put in high wind. If you have a chimney with more than one flue, this is the cap you want.
Custom Cap
Some chimneys don’t fit a standard cap: oversized flues, odd shapes, or a crown that’s wider than usual. In those cases we have a cap made to the exact dimensions rather than forcing a stock size that leaves gaps. Custom caps are also a good choice when you want a particular look to match the house. We take the measurements during the inspection and tell you what the lead time looks like before you commit.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a curated roster of professional-grade chimney brands because the materials matter as much as the install. Olympia Chimney makes caps and components we fit regularly, and we know where their mounting hardware holds up and where it needs extra attention. Famco caps are another common sight on Fox Chase rooftops, and we’re familiar with how their sizing works so the fit is right the first time.
For crown work and related masonry, we rely on materials from Copperfield and DuraFlex where they suit the job, and we use the same professional-grade supplies chimney specialists trust rather than big-box substitutes. Whether you have Olympia Chimney, Famco, or any other make on your roof, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Rusted or missing cap. A cap that’s rusted through or blown off leaves the flue open to rain and animals. Even a small gap lets water in, and once it’s inside the flue it has nowhere to go but down.
- Cracked or crumbling crown. Hairline cracks in the crown widen with every freeze and thaw. Left alone, water gets into the masonry and the damage moves inward toward the flue.
- Water stains or damp spots near the chimney. Brown stains on the ceiling or a damp patch on the chimney breast often trace back to a failed crown or an unsealed cap base. It’s worth having it looked at before the next storm.
- Animals or nesting debris in the flue. Birds and squirrels get in through an uncapped or damaged flue and build nests that block the draft. A proper cap with intact screening stops that from happening.
- Loose mortar or spalling brick near the top. When the crown fails, water works into the brick below and mortar starts to crumble. Catching it at the crown stage is far less expensive than repairing the chimney body.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection and photo evidence. We get on the roof, look at the cap, crown, flue tile, and the top few courses of brick, and photograph what we find. You see the pictures before we recommend anything, so you’re not taking our word for it.
- 2
Written scope and flat price. We tell you what we found, what it means, and what fixing it involves, then put it in writing with a flat price agreed before any work starts. If the crown only needs a coating, we’ll say so.
- 3
Prep and protection. Before we touch the crown, we clear loose material, protect the roof and siding below, and make sure the flue is clear. Proper prep is what makes a repair last more than a season.
- 4
Repair or install. We rebuild or coat the crown, install or replace the cap, and seal it correctly. Materials come from brands like Olympia Chimney, Famco, and Copperfield, matched to the job rather than whatever’s on hand.
- 5
Final check and report. We confirm the cap is secure, the crown sheds water the way it should, and the flue is clear, then hand you the photos and a short report. If anything can safely wait, we’ll tell you that too.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Fox Chase?
A typical chimney cap installation in Fox Chase runs $150 – $450 depending on flue count and cap material, and a crown repair typically runs $300 – $700 depending on how much of the crown needs rebuilding.
| Service | Typical Estimated Range |
|---|---|
| Single-flue cap installation | $150 – $350 |
| Multi-flue or custom cap | $300 – $600 |
| Crown repair (partial rebuild) | $300 – $700 |
| Crown coating | $250 – $500 |
| Full crown rebuild | $600 – $1,200 |
What moves the price: the number of flues, the cap material (galvanized versus stainless), how much of the crown has failed, and whether the flue tile underneath needs attention once the old cap comes off. You avoid overpaying by getting the photo evidence first and asking for a written scope before anyone starts. Our free estimate includes the roof inspection, photos, and a flat written price, so the number you agree to is the number you pay. Call (844) 526-7704 for an exact quote.
Chimney Cap & Crown Near Fox Chase – Our Service Area
We cover Fox Chase and the surrounding neighborhoods, including chimney cap & crown work in Chestnut Hill, plus Roxborough, Manayunk, and Upper Moreland. Response times depend on the day and the job, and we’ll give you a realistic window when you book. If you’re nearby, call and we’ll find the next opening. Reach us at (844) 526-7704.
Serving Fox Chase, PA – Our Local Coverage Area
We serve Fox Chase and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Fox Chase
A chimney cap is the cover over the flue opening that keeps out rain, animals, and debris, and the crown is the concrete or mortar top of the masonry that sheds water away from the chimney body. Together they’re the first line of defense against water damage. If either one fails, water gets into the chimney and shows up later as stains, crumbling mortar, or a damaged flue. Call (844) 526-7704 for an exact quote – estimates are free.
Most cap installations take under an hour once we’re on the roof, and crown repairs or coatings usually take a few hours depending on how much material needs to come out. A full crown rebuild takes longer because the new crown has to cure properly. We’ll give you a realistic time when we book the job. Call (844) 526-7704 to schedule.
A typical single-flue cap installation runs $150 – $350, and a crown repair typically runs $300 – $700 depending on how much needs rebuilding. Full crown rebuilds and custom or multi-flue caps cost more, and the written estimate sets the final price. We give you the photo evidence and a flat price before any work starts. Call (844) 526-7704 for an exact quote – estimates are free.
Yes. We work with Olympia Chimney and Famco caps regularly and know how their sizing and mounting hardware behave on Fox Chase roofs. We also handle Copperfield and DuraFlex components where they suit the job. Whether you have Olympia Chimney, Famco, or any other make, we can help.
We can often get to cap and crown jobs the same day, depending on the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening. Call (844) 526-7704 to see what’s available.
Our workmanship and the materials we install are covered, and we’ll put the details in writing with your estimate so you know exactly what’s covered. Caps from brands like Olympia Chimney and Famco carry their own manufacturer coverage. Ask us about the specifics when we’re on site. Call (844) 526-7704 for an exact quote – estimates are free.
Clear access to the fireplace and the area around the chimney inside the house, and make sure we can get to the roof safely. Move any vehicles out of the way if we’ll be working above a driveway. That’s usually all it takes, and we’ll handle the rest. Call (844) 526-7704 to book.
Schedule Your Chimney Cap & Crown Service in Fox Chase Today
A rusted cap or a cracked crown gets worse with every freeze, and it’s one of the least expensive chimney repairs to catch early. We inspect, show you the photos, and give you a written flat price before any work begins. Call (844) 526-7704. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. No-obligation estimate.
Written by the team at Chimney Sweep Fox Chase.